Sangoma PRI ISDN Issue

inspireit · Joined: 02 Jun 2010 Posts: 1

Hi,

I am running elastix with a sangoma PRI card. I am having trouble making it work on the public network - it shows as connected but calls arent allowed in or out. I have pasted status/debug information below - any assistance would be appreciated.

pbx-norwest*CLI> pri show
debug span spans version
pbx-norwest*CLI> pri show span 1
Primary D-channel: 16
Status: Provisioned, Up, Active
Switchtype: EuroISDN
Type: CPE
Window Length: 0/7
Sentrej: 0
SolicitFbit: 0
Retrans: 0
Busy: 0
Overlap Dial: -1
Logical Channel Mapping: 0
T200 Timer: 1000
T203 Timer: 10000
T305 Timer: 30000
T308 Timer: 4000
T309 Timer: -1
T313 Timer: 4000
N200 Counter: 3

-- Remote UNIX connection
-- Remote UNIX connection disconnected
pbx-norwest*CLI> pri debug span 1
Enabled debugging on span 1
-- Got SABME from network peer.
Sending Unnumbered Acknowledgement
q921.c:858 q921_reset: q921_state now is Q921_LINK_CONNECTION_RELEASED
q921.c:805 q921_dchannel_up: q921_state now is Q921_LINK_CONNECTION_ESTABLISHED
-- Got SABME from network peer.
Sending Unnumbered Acknowledgement
q921.c:858 q921_reset: q921_state now is Q921_LINK_CONNECTION_RELEASED
q921.c:805 q921_dchannel_up: q921_state now is Q921_LINK_CONNECTION_ESTABLISHED
-- Got SABME from network peer.
Sending Unnumbered Acknowledgement
q921.c:858 q921_reset: q921_state now is Q921_LINK_CONNECTION_RELEASED
q921.c:805 q921_dchannel_up: q921_state now is Q921_LINK_CONNECTION_ESTABLISHED
-- Got SABME from network peer.
Sending Unnumbered Acknowledgement
q921.c:858 q921_reset: q921_state now is Q921_LINK_CONNECTION_RELEASED
q921.c:805 q921_dchannel_up: q921_state now is Q921_LINK_CONNECTION_ESTABLISHED
-- Got SABME from network peer.
Sending Unnumbered Acknowledgement
q921.c:858 q921_reset: q921_state now is Q921_LINK_CONNECTION_RELEASED
q921.c:805 q921_dchannel_up: q921_state now is Q921_LINK_CONNECTION_ESTABLISHED
pbx-norwest*CLI> exit
[root@pbx-norwest ~]#

[root@pbx-norwest ~]# wanrouter status

Devices currently active:
wanpipe1

Wanpipe Config:

Device name | Protocol Map | Adapter | IRQ | Slot/IO | If's | CLK | Baud rate |
wanpipe1 | N/A | A101/2 | 233 | 2 | 1 | N/A | 0 |

Wanrouter Status:

Device name | Protocol | Station | Status |
wanpipe1 | AFT TE1 | N/A | Connected |

[root@pbx-norwest ~]# wanrouter list

Devices currently active:
wanpipe1

[root@pbx-norwest ~]# wanrouter hwprobe

-------------------------------
| Wanpipe Hardware Probe Info |
-------------------------------
1 . AFT-A101u : SLOT=2 : BUS=10 : IRQ=11 : CPU=A : PORT=PRI : V=25

Card Cnt: A101-2=1

[root@pbx-norwest ~]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:13:72:59:51:1E
inet addr:10.20.0.245 Bcast:10.20.0.255 Mask:255.255.255.0
inet6 addr: fe80::213:72ff:fe59:511e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1001 errors:0 dropped:0 overruns:0 frame:0
TX packets:634 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:103170 (100.7 KiB) TX bytes:70801 (69.1 KiB)
Base address:0xecc0 Memory:dfae0000-dfb00000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:144 errors:0 dropped:0 overruns:0 frame:0
TX packets:144 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:73725 (71.9 KiB) TX bytes:73725 (71.9 KiB)

w1g1 Link encap:Point-to-Point Protocol
UP POINTOPOINT RUNNING NOARP MTU:240 Metric:1
RX packets:235214 errors:0 dropped:0 overruns:0 frame:0
TX packets:235212 errors:0 dropped:0 overruns:0 carrier:3
collisions:0 txqueuelen:100
RX bytes:56451360 (53.8 MiB) TX bytes:56450880 (53.8 MiB)
Interrupt:233 Memory:ffffc20000020c00-ffffc20000022bff

[root@pbx-norwest ~]# wanrouter summary

Configuration File Summary in : /etc/wanpipe/

Device Protocol Type Cpu/Io Slot/Irq Bus State
------------------------------------------------------------------------
wanpipe1 WAN_AFT PCI A 2 10 Connected
[root@pbx-norwest ~]#

pbx-norwest*CLI> dahdi show channels

pseudo default default
1 from-pstn default
2 from-pstn default
3 from-pstn default
4 from-pstn default
5 from-pstn default
6 from-pstn default
7 from-pstn default
8 from-pstn default
9 from-pstn default
10 from-pstn default
11 from-pstn default
12 from-pstn default
13 from-pstn default
14 from-pstn default
15 from-pstn default
17 from-pstn default
18 from-pstn default
19 from-pstn default
20 from-pstn default
21 from-pstn default
22 from-pstn default
23 from-pstn default
24 from-pstn default
25 from-pstn default
26 from-pstn default
27 from-pstn default
28 from-pstn default
29 from-pstn default
30 from-pstn default
31 from-pstn default

pbx-norwest*CLI> dahdi show status
Description Alarms IRQ bpviol CRC4
wanpipe1 card 0 OK 0 0 0