Posted: Fri Oct 15, 2004 2:18 pm Post subject: [Asterisk-bsd] TDM400P FXS on FreeBSD 5.2.1-release - sanity
OK, now that I've got the power connector actually connected, and the
zaptel driver recognizes my FXS port, I want to verify that the board
is supposed to be generating a dialtone, because I don't get one.
The driver shows the following when I load it:
Zapata Telephony Interface Registered on major 196
FXS device: vendor=e159 device=1 subvendor=b100
wcfxs0: <Wildcard TDM400P REV E/F> port 0xe800-0xe8ff mem
0xfebff000-0xfebfffff irq 27 at device 2.0 on pci1
FXS Attach for wcfxs0: deviceID : 0xe159
Freshmaker version: 71
Freshmaker passed register test
Module 0: Installed -- AUTO FXS
Module 1: Installed -- AUTO FXO
Module 2: Not installed
Module 3: Not installed
Found a Wildcard TDM: Wildcard TDM400P REV E/F (4 modules)
Registered tone zone 0 (United States / North America)
I've added the following to /usr/local/etc/zaptel.conf:
fxoks=1
fxsks=2
loadzone=us
defaultzone=us
When I run ztcfg, it show this:
Keyword: [fxoks], Value: [1]
Keyword: [fxsks], Value: [2]
Keyword: [loadzone], Value: [us]
Keyword: [defaultzone], Value: [us]
My assumption is that at this point, I should be able to plug an analog
phone into channel 1 and hear a dialtone generated by the board... I
don't. Am I wrong, here? Any suggestions what to try next? I'm going
to forge ahead and do some configuration of asterisk to test out the FXO
port anyway, but I was hoping to get some confirmation that the FXS
port might actually work...
Posted: Fri Oct 15, 2004 2:49 pm Post subject: [Asterisk-bsd] TDM400P FXS on FreeBSD 5.2.1-release - sanity
It would seem that once I got more of the asterisk configuration
completed, I got my much sought-after dialtone, and have been able to
terminate SIP calls onto an analog phone.
So, looks like the TDM400P FXS support works!
(At least with the limited testing I've done)
Thanks and sorry for the noise,
+j
Jeff Rizzo wrote:
Quote:
OK, now that I've got the power connector actually connected, and
the zaptel driver recognizes my FXS port, I want to verify that the
board is supposed to be generating a dialtone, because I don't get one.
The driver shows the following when I load it:
Zapata Telephony Interface Registered on major 196
FXS device: vendor=e159 device=1 subvendor=b100
wcfxs0: <Wildcard TDM400P REV E/F> port 0xe800-0xe8ff mem
0xfebff000-0xfebfffff irq 27 at device 2.0 on pci1
FXS Attach for wcfxs0: deviceID : 0xe159
Freshmaker version: 71
Freshmaker passed register test
Module 0: Installed -- AUTO FXS
Module 1: Installed -- AUTO FXO
Module 2: Not installed
Module 3: Not installed
Found a Wildcard TDM: Wildcard TDM400P REV E/F (4 modules)
Registered tone zone 0 (United States / North America)
I've added the following to /usr/local/etc/zaptel.conf:
fxoks=1
fxsks=2
loadzone=us
defaultzone=us
When I run ztcfg, it show this:
Keyword: [fxoks], Value: [1]
Keyword: [fxsks], Value: [2]
Keyword: [loadzone], Value: [us]
Keyword: [defaultzone], Value: [us]
My assumption is that at this point, I should be able to plug an
analog phone into channel 1 and hear a dialtone generated by the
board... I don't. Am I wrong, here? Any suggestions what to try
next? I'm going to forge ahead and do some configuration of asterisk
to test out the FXO port anyway, but I was hoping to get some
confirmation that the FXS port might actually work...
Posted: Sat Oct 16, 2004 12:22 am Post subject: [Asterisk-bsd] TDM400P FXS on FreeBSD 5.2.1-release - sanity
Let us know how you get on.
Thanks
Chris
----- Original Message -----
From: "Jeff Rizzo" <riz+asterisk@boogers.sf.ca.us>
To: "Asterisk on BSD discussion" <asterisk-bsd@lists.digium.com>
Sent: Friday, October 15, 2004 11:49 PM
Subject: Re: [Asterisk-bsd] TDM400P FXS on FreeBSD 5.2.1-release - sanity
check
Quote:
It would seem that once I got more of the asterisk configuration
completed, I got my much sought-after dialtone, and have been able to
terminate SIP calls onto an analog phone.
So, looks like the TDM400P FXS support works!
(At least with the limited testing I've done)
Thanks and sorry for the noise,
+j
Jeff Rizzo wrote:
> OK, now that I've got the power connector actually connected, and the
> zaptel driver recognizes my FXS port, I want to verify that the board is
> supposed to be generating a dialtone, because I don't get one.
>
> The driver shows the following when I load it:
>
> Zapata Telephony Interface Registered on major 196
> FXS device: vendor=e159 device=1 subvendor=b100
> wcfxs0: <Wildcard TDM400P REV E/F> port 0xe800-0xe8ff mem
> 0xfebff000-0xfebfffff irq 27 at device 2.0 on pci1
> FXS Attach for wcfxs0: deviceID : 0xe159
> Freshmaker version: 71
> Freshmaker passed register test
> Module 0: Installed -- AUTO FXS
> Module 1: Installed -- AUTO FXO
> Module 2: Not installed
> Module 3: Not installed
> Found a Wildcard TDM: Wildcard TDM400P REV E/F (4 modules)
> Registered tone zone 0 (United States / North America)
>
> I've added the following to /usr/local/etc/zaptel.conf:
>
> fxoks=1
> fxsks=2
> loadzone=us
> defaultzone=us
>
> When I run ztcfg, it show this:
> Keyword: [fxoks], Value: [1]
> Keyword: [fxsks], Value: [2]
> Keyword: [loadzone], Value: [us]
> Keyword: [defaultzone], Value: [us]
>
> My assumption is that at this point, I should be able to plug an analog
> phone into channel 1 and hear a dialtone generated by the board... I
> don't. Am I wrong, here? Any suggestions what to try next? I'm going
> to forge ahead and do some configuration of asterisk to test out the FXO
> port anyway, but I was hoping to get some confirmation that the FXS port
> might actually work...
>
> Thanks,
> +j
>
> _______________________________________________
> Asterisk-BSD mailing list
> Asterisk-BSD@lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-bsd
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum