Posted: Mon Mar 30, 2009 9:42 pm Post subject: [Asterisk-bsd] Zaptel Not Working After Upgrading OS & Aster
I just rebuilt my server and installed FreeBSD-7.2-PRERELEASE-i386. I updated the ports and installed Asterisk-1.4.23.1 with Zaptel-1.4.11. My system has an X101P card and all was working well until I updated. I can put the old hard drive back in and all works well. But the new setup is missing something. Other than Zaptel Asterisk works fine.
I can start Asterisk and check voicemail and listen to MOH. But when I run zttool it shows there is nothing there.
There doesn't seem to be any error messages at boot time with zaptel. And as you can see above, kldstat shows the card modules got loaded and dmesg shows this:
Zapata Telephony Interface Registered on major 196
Zaptel Version: zaptel-bsd-ng v0.0.1
Zaptel Echo Canceller: MG2
link_elf: symbol te11xp_remove_one undefined
Posted: Mon Mar 30, 2009 10:08 pm Post subject: [Asterisk-bsd] Zaptel Not Working After Upgrading OS & Aster
this zaptel version very unstable
some cards does not work fine
rollback to version 1.4.6 if it possible
Frank Griffith пишет:
Quote:
I just rebuilt my server and installed FreeBSD-7.2-PRERELEASE-i386. I updated the ports and installed Asterisk-1.4.23.1 with Zaptel-1.4.11. My system has an X101P card and all was working well until I updated. I can put the old hard drive back in and all works well. But the new setup is missing something. Other than Zaptel Asterisk works fine.
I can start Asterisk and check voicemail and listen to MOH. But when I run zttool it shows there is nothing there.
There doesn't seem to be any error messages at boot time with zaptel. And as you can see above, kldstat shows the card modules got loaded and dmesg shows this:
Zapata Telephony Interface Registered on major 196
Zaptel Version: zaptel-bsd-ng v0.0.1
Zaptel Echo Canceller: MG2
link_elf: symbol te11xp_remove_one undefined
Any advice?
Quote:
_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.com--
Posted: Mon Mar 30, 2009 11:37 pm Post subject: [Asterisk-bsd] Zaptel Not Working After Upgrading OS & Aster
Thanks, but how does run roll back a port?
Would I be better off to deinstall zaptel port and then install zaptel-1.4.6 from source. I prefer this method but the damn dependencies always foul things up if one doesn't use the ports.
--- On Mon, 3/30/09, Roman Shubovich <r.shubovich@elcomnet.ru> wrote:
Quote:
From: Roman Shubovich <r.shubovich@elcomnet.ru>
Subject: Re: [Asterisk-bsd] Zaptel Not Working After Upgrading OS & Asterisk
To: glassdude45@yahoo.com, "Asterisk on BSD discussion" <>
Date: Monday, March 30, 2009, 7:01 PM
this zaptel version very unstable
some cards does not work fine
rollback to version 1.4.6 if it possible
Frank Griffith пишет:
Quote:
I just rebuilt my server and installed FreeBSD-7.2-PRERELEASE-i386. I updated the ports and installed Asterisk-1.4.23.1 with Zaptel-1.4.11. My system has an X101P card and all was working well until I updated. I can put the old hard drive back in and all works well. But the new setup is missing something. Other than Zaptel Asterisk works fine.
I can start Asterisk and check voicemail and listen to MOH. But when I run zttool it shows there is nothing there.
There doesn't seem to be any error messages at boot time with zaptel. And as you can see above, kldstat shows the card modules got loaded and dmesg shows this:
Zapata Telephony Interface Registered on major 196
Zaptel Version: zaptel-bsd-ng v0.0.1
Zaptel Echo Canceller: MG2
link_elf: symbol te11xp_remove_one undefined
Any advice?
Quote:
_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.com--
Posted: Mon Mar 30, 2009 11:50 pm Post subject: [Asterisk-bsd] Zaptel Not Working After Upgrading OS & Aster
I just noticed that the new zaptel-1.4.11 does not load wcfxo.ko. I need this module for the X101P analog card in my system. Was this removed from the new port or is there a way I can build from the port and get the wcfxo.ko module included?
--- On Mon, 3/30/09, Roman Shubovich <r.shubovich@elcomnet.ru> wrote:
Quote:
From: Roman Shubovich <r.shubovich@elcomnet.ru>
Subject: Re: [Asterisk-bsd] Zaptel Not Working After Upgrading OS & Asterisk
To: glassdude45@yahoo.com, "Asterisk on BSD discussion" <asterisk-bsd@lists.digium.com>
Date: Monday, March 30, 2009, 7:01 PM
this zaptel version very unstable
some cards does not work fine
rollback to version 1.4.6 if it possible
Frank Griffith пишет:
Quote:
I just rebuilt my server and installed FreeBSD-7.2-PRERELEASE-i386. I updated the ports and installed Asterisk-1.4.23.1 with Zaptel-1.4.11. My system has an X101P card and all was working well until I updated. I can put the old hard drive back in and all works well. But the new setup is missing something. Other than Zaptel Asterisk works fine.
I can start Asterisk and check voicemail and listen to MOH. But when I run zttool it shows there is nothing there.
There doesn't seem to be any error messages at boot time with zaptel. And as you can see above, kldstat shows the card modules got loaded and dmesg shows this:
Zapata Telephony Interface Registered on major 196
Zaptel Version: zaptel-bsd-ng v0.0.1
Zaptel Echo Canceller: MG2
link_elf: symbol te11xp_remove_one undefined
Any advice?
Quote:
_______________________________________________
--Bandwidth and Colocation Provided by http://www.api-digital.com--
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
