Posted: Wed Jan 05, 2005 1:59 pm Post subject: [Asterisk-bsd] TDM400P Rev E/F, "Module not installed"
I've been running Asterisk in the office here for a little over a year
on a debian machine - I'm *overjoyed* that the zaptel drivers are now
functional under FreeBSD.
With that said, I'm seeing an issue that I don't think is
(mis)configuration (based on the configs on my debian boxes). 3 out
of 4 of the ports on my TDM400P are dead - dmesg claims "Module not
installed". (Yes, it has the power cable plugged in. :)
I see a related post a few months prior, noting that the problem was
fixed. Did it just not filter to the ports tree as of yet?
Relevent info I could think to include is below - any info on how to get
this working is appreciated!
% dmesg
kernel: Zapata Telephony Interface Registered on major 196
kernel: ZapTel device: vendor=e159 device=1 subvendor=8085
kernel: wcfxo0: <Wildcard X101P> port 0xa400-0xa4ff mem 0xde001000-0xde001fff irq 20 at device 10.0 on pci2
kernel: ZapTel Attach for wcfxo0: deviceID : 0xe159
kernel: wcfxo0: [GIANT-LOCKED]
kernel: wcfxo: DAA mode is 'FCC'
kernel: Found a Wildcard FXO: Wildcard X101P
kernel: ZapTel device loaded.
kernel: FXS device: vendor=e159 device=1 subvendor=b100
kernel: wcfxs0: <Wildcard TDM400P REV E/F> port 0xa000-0xa0ff mem 0xde000000-0xde000fff irq 21 at device 7.0 on pci2
kernel: FXS Attach for wcfxs0: deviceID : 0xe159
kernel: wcfxs0: [GIANT-LOCKED]
kernel: Freshmaker version: 63
kernel: Freshmaker passed register test
kernel: Module 0: Installed -- AUTO FXS
kernel: Module 1: Not installed
kernel: Module 2: Not installed
kernel: Module 3: Not installed
kernel: Found a Wildcard TDM: Wildcard TDM400P REV E/F (4 modules)
kernel: Registered tone zone 0 (United States / North America)
Posted: Wed Jan 05, 2005 10:02 pm Post subject: [Asterisk-bsd] TDM400P Rev E/F, "Module not installed"
On 06/01/2005 05:42 Mahlon E. Smith said the following:
Quote:
(mis)configuration (based on the configs on my debian boxes). 3 out
of 4 of the ports on my TDM400P are dead - dmesg claims "Module not
installed". (Yes, it has the power cable plugged in. :)
have you tried swapping the modules around on the card to see if the
problem follows the module ?
--
Regards, /\_/\ "All dogs go to heaven."
dinesh@alphaque.com (0 0) http://www.alphaque.com/
+==========================----oOO--(_)--OOo----==========================+
| for a in past present future; do |
| for b in clients employers associates relatives neighbours pets; do |
| echo "The opinions here in no way reflect the opinions of my $a $b." |
| done; done |
+=========================================================================+
Posted: Wed Jan 05, 2005 10:41 pm Post subject: [Asterisk-bsd] TDM400P Rev E/F, "Module not installed"
On Thu, Jan 06, 2005, Dinesh Nair wrote:
Quote:
On 06/01/2005 05:42 Mahlon E. Smith said the following:
>(mis)configuration (based on the configs on my debian boxes). 3 out
>of 4 of the ports on my TDM400P are dead - dmesg claims "Module not
>installed". (Yes, it has the power cable plugged in. :)
have you tried swapping the modules around on the card to see if the
problem follows the module ?
I hadn't tried that yet - great idea, and it appears that the one
working module does indeed change based on where it's sitting. I can't
believe I've got 3 fried modules... this card must have been seriously,
seriously zapped. I'll take this up with Digium from here on out.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum